Back to blog

Australia’s December 1 exposure-limit change: what each jurisdiction has confirmed

Australia’s WEL list is due December 1, 2026. What each state, territory and mining regime had confirmed by November 18, including the 2028 and 2029 exceptions.

October 7, 2026. Updated November 18, 2026.

Safe Work Australia’s Workplace exposure limits for airborne contaminants (the WEL list) is due to replace the workplace exposure standards (WES) list on December 1, 2026. Safe Work Australia’s transition page says WHS ministers agreed to a harmonised start on that date, once each jurisdiction has put the WEL into its own WHS laws. Until then the WES list still applies, and Safe Work Australia refers questions about local implementation to each WHS or mining regulator.

The national WEL transition record tracks the national date. This update adds what each jurisdiction’s legislation register or regulator showed when we checked on November 18, 2026. Several jurisdictions have kept older values or set later dates for particular substances, so the national date does not settle every entry at every site.

Jurisdiction by jurisdiction

  • Commonwealth: Comcare’s June 5, 2026 notice says the WEL replaces the WES from December 1, 2026. We found no registered amendment to the Commonwealth WHS Regulations naming the WEL list on the Federal Register of Legislation.
  • New South Wales: SafeWork NSW says the Work Health and Safety Amendment (Harmonisation) Regulation 2026 adopts the WEL list and commences December 1, 2026. NSW keeps the current phosphine standards until June 30, 2028 and sets an interim diesel particulate limit until the same date, with the national values applying from July 1, 2028. The NSW legislation register returned a bot check, so this entry rests on the regulator’s summary.
  • Victoria: Victoria regulates under its own Occupational Health and Safety Act 2004. The OHS Amendment (Workplace Exposure Limits) Regulations 2026, S.R. No. 165/2026, commence December 1, 2026 and keep older limits for listed substances in a new Schedule 8A. WorkSafe Victoria says 15 substances move to the WEL values on December 1, 2029. The government’s notice of decision says the rest of that transition will be provided for when the OHS Regulations are remade.
  • Queensland: WorkSafe Queensland says most WELs apply from December 1, 2026, with transition arrangements for the same 15 substances until December 1, 2029. We did not locate the amending regulation on the Queensland register.
  • Western Australia: The Work Health and Safety Legislation (Workplace Exposure Limits) Amendment Regulations 2026 (SL 2026/230), published November 11, 2026, commence December 1, 2026. They adopt the November 2025 WEL list in both the General and the Mines Regulations, keep the older phosphine values until November 30, 2029, and change the diesel particulate entry.
  • South Australia: SafeWork SA says the WEL list applies from December 1, 2026 except for phosphine, flour dust, grain dust and methyl bromide. Its October 26 notice puts the grain dust, flour dust and methyl bromide values no earlier than July 2028.
  • Tasmania: WorkSafe Tasmania says the new limits arrive on December 1, 2026 and apply to all Tasmanian workplaces. We did not check a Tasmanian instrument.
  • Australian Capital Territory: WorkSafe ACT says the WEL replaces the WES from December 1, 2026. On November 18 the ACT register still listed NI2026-340, which declares the November 2025 WES list from September 9, 2026, as the current exposure declaration. We found no ACT declaration of the WEL list.
  • Northern Territory: We could not confirm the NT position. NT WorkSafe’s summary of law amendments lists no WEL change, and we found no NT WorkSafe page on the transition.

Mining regimes

Queensland mines and quarries sit under separate mining safety legislation. Schedule 5 of the Mining and Quarrying Safety and Health Regulation 2017 still refers to the WES document, lists welding fumes and respirable crystalline silica separately and leaves diesel particulate matter out of its general incorporation. Our story on the Queensland mining baseline covers those entries. We did not confirm how Queensland coal mines will move to the WEL list.

In Western Australia, Part 3 of SL 2026/230 applies the WEL list to mines from December 1, 2026 with a mines-specific diesel particulate value. NSW’s Resources Regulator still describes the mining diesel standard that began on February 1, 2021, and we did not confirm how the December amendments apply at NSW mines. WorkSafe Victoria says underground mining keeps a separate diesel particulate limit.

Practical notes for an exposure register

APT’s practical interpretation is to record the instrument and list edition that governs each site and sector. Safe Work Australia’s current list is dated November 2026 and corrects a few entries, while Western Australia’s regulations name the November 2025 edition. Diesel particulate matter, phosphine and the 15 Victorian and Queensland transition substances need their own local check. Samples taken before a jurisdiction’s start date stay compared with the WES value that applied at the time.

Safe Work Australia’s paired air-monitoring guides replace its older interpretation guidance on December 1. For other Australian, US and Canadian developments, see the industrial hygiene regulatory tracker.

Get regulatory news updates

Receive updates on industrial hygiene and workplace exposure regulations in the US, Canada, and Australia.

Take a tour of APT's dust management platform

Vulcan Materials Company is the nation’s largest producer of construction aggregates.

Project partner

Brent Leclerc | Environmental Manager

Problems solved

Unjustified community dust complaints & lawsuits

Difficulty complying with opacity regulations and risk of NOVs

Solution

Real-time dust monitoring

Dust maps proving no community impact, preventing fines & lawsuits

Real-time opacity monitoring, high degree of compliance

Case study overview

Share this article

Better decisions start with real-time insight

APT helps industrial teams move faster, act smarter, and stay compliant—because when you can see the problem clearly, you can solve it confidently.