Back to blog

Quebec draft would lower RSST limits for benzene, xylene and hardwood dust

Quebec's November 2026 draft would replace the RSST Schedule I exposure table, lowering benzene, xylene and hardwood dust limits. Comments close December 26.

November 18, 2026

Benzene, xylene, hardwood dust and titanium dioxide would all get lower permissible exposure values in Quebec under a draft regulation the CNESST published in the Gazette officielle du Québec on November 11, 2026. The draft, the Règlement modifiant le Règlement sur la santé et la sécurité du travail et le Code de sécurité pour les travaux de construction, would replace the entire air-contaminant table in Part 1 of Schedule I to the Regulation respecting occupational health and safety (RSST). The CNESST can adopt it and submit it for government approval after a 45-day comment period. Until a final regulation is approved and published, the current Schedule I values remain the legal limits.

APT’s Quebec draft exposure-limit table record sets the proposed values beside the current ones for the substances discussed here.

Proposed values for common substances

Quebec states most limits as a VEMP, an average over an eight-hour day in a 40-hour week, and a VECD, a 15-minute short-term value. The comparison below uses the current RSST consolidation on Légis Québec, up to date to July 1, 2026.

  • Benzene’s VEMP would drop from 0.5 ppm to 0.2 ppm, and its VECD from 2.5 ppm to 1 ppm.
  • Xylene (o, m and p isomers) would drop from 100 ppm VEMP and 150 ppm VECD to 20 ppm VEMP, with no VECD.
  • Hardwood dust, which now shares a 5 mg/m³ total-dust entry with softwood dust, would get a separate 1 mg/m³ entry.
  • Softwood dust other than western red cedar would stay at 5 mg/m³, with the measured fraction changing from total dust to inhalable dust.
  • Titanium dioxide would move from 10 mg/m³ as total dust to 3 mg/m³ for respirable fine particles.
  • Paraquat, as the cation, now has a 0.5 mg/m³ value with no fraction notation and a 0.1 mg/m³ respirable value; the draft replaces both with one 0.05 mg/m³ inhalable value.
  • Methyl ethyl ketone would go up, from 50 ppm VEMP and 100 ppm VECD to 75 ppm and 150 ppm.

Other proposed decreases include epichlorohydrin from 2 ppm to 0.1 ppm, cyclohexene from 300 ppm to 20 ppm, methylcyclohexane from 400 ppm to 100 ppm and halothane from 50 ppm to 5 ppm. Phosgene would move from a 0.1 ppm VEMP to a 0.02 ppm ceiling. Fentanyl and clothianidine would get new entries, and magnesite would be removed. The full draft table runs from page 6054 to page 6089 of the issue, so any substance not listed here needs its own check.

The notation for the new hardwood dust entry is printed as “P”, which the draft defines as a ceiling value. The softwood and western red cedar entries are marked Pi, the inhalable fraction. The final text may clarify which basis applies to hardwood dust.

Silica and several metals keep their current values

Respirable quartz and cristobalite stay at 0.05 mg/m³ in the draft table. Beryllium, lead, cadmium, cobalt, manganese and Portland cement also keep their current values.

This draft is separate from Décret 280-2024, the earlier Schedule I amendment whose delayed entries took effect on March 1, 2026. That amendment has its own Quebec staged exposure-limit record.

Comment deadline and start dates

The 45-day comment period counts from November 11 and ends on December 26, 2026. Written comments go to the CNESST’s vice-president of prevention at the address in the Gazette notice.

Section 8 of the draft would bring the regulation into force 60 days after the final version is published. It lists two exceptions, both written for provisions of section 2. Those concerning xylene and clothianidine would start two years after publication, and the rest of section 2 on the 15th day after publication. Section 2 only repeals RSST section 271, and the table changes are in section 3. Read literally, the new table would fall under the general 60-day rule and the two-year delay for xylene would apply to nothing. If the exceptions were meant to refer to section 3, most new values would start on the 15th day after publication and the xylene and clothianidine entries two years after publication. The final text may correct the reference, so no start date for the new values can be settled from the draft.

The same draft would also apply RSST sections 172 to 194 on machine safety to construction sites and amend the Code de sécurité pour les travaux de construction (Safety Code for the construction industry) to match.

Reviewing a Quebec exposure register against the draft

In APT’s reading, compliance records should keep the current Schedule I values until a final regulation takes effect. A useful first step is to compare the site’s substance inventory with the draft table, starting with benzene, xylene, hardwood dust and titanium dioxide. Tasks whose recent results sit between the current and proposed values are the ones a lower limit would affect first.

Changes in the measured fraction also affect sampling. Softwood dust would be assessed as inhalable dust and titanium dioxide as respirable fine particles, which can change the sampler used. WorkSafeBC has consulted on the same 0.2 ppm eight-hour benzene value, as described in APT’s British Columbia benzene review record.

Other Canadian proposals and adopted exposure-limit changes are listed in the industrial hygiene regulatory tracker.

Get regulatory news updates

Receive updates on industrial hygiene and workplace exposure regulations in the US, Canada, and Australia.

Take a tour of APT's dust management platform

Vulcan Materials Company is the nation’s largest producer of construction aggregates.

Project partner

Brent Leclerc | Environmental Manager

Problems solved

Unjustified community dust complaints & lawsuits

Difficulty complying with opacity regulations and risk of NOVs

Solution

Real-time dust monitoring

Dust maps proving no community impact, preventing fines & lawsuits

Real-time opacity monitoring, high degree of compliance

Case study overview

Share this article

Better decisions start with real-time insight

APT helps industrial teams move faster, act smarter, and stay compliant—because when you can see the problem clearly, you can solve it confidently.